View BA10339XX_7680113.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

datashee t product structure : silicon monolithic integrated circuit this product has no designed protec tion against radioactive rays 1/53 ? 2013 rohm co., ltd. all rights reserved. www.rohm.com tsz02201-0rfr0g200200-1-2 tsz22111 ? 14 ? 001 11.dec.2013 rev.003 comparators ground sense comparator ba8391g ba103 93f BA10339XX ba2903xxx ba2903sxxx ba2903wxx ba290 1xx ba2901sxx general description general purpose ba8391g/ba10393f/BA10339XX and high reliability ba2903xxxx/ba2901xxx integrate one, two or four independent high gain voltage comparator. some features are the wide operating voltage that is 2v to 36v (for ba8391g/ba10393f/ ba2903xxxx/ba2901xxx) 3v to 36v (for BA10339XX) and low supply current. therefore, this series is suitable for any application. features ? operable with a single power supply ? wide operating supply voltage ? standard comparator pin assignments ? input and output are ground sense operated ? open collector ? wide temperature range application ? general purpose ? current monitor ? battery monitor ? multivibrators key specifications ? wide operating supply voltage(single supply): ba8391g/ba10393f +2.0v to +36.0v ba2903xxx/ba2901xxxx +2.0v to +36.0v BA10339XX +3.0v to +36.0v ? wide operating supply voltage(split supply): ba8391g/ba10393f 1.0v to 18.0v ba2903xxxx/ba2901xxx 1.0v to 18.0v BA10339XX 1.5v to 18.0v ? wide temperature range: ba8391g/ba10393f/BA10339XX -40c to +85c ba2903sxxx/ba2901sxx -40c to +105c ba2903xxx/ba2901xx -40c to +125c ? input offset voltage: ba2903sxxx/ba2901sxx 7mv(max) ba8391g/ba2903xxx/ba2901xx 7mv(max) ba10393f/BA10339XX 5mv(max) ba2903wxx 2mv(max) packages w(typ) x d(typ) x h(max) ssop5 2.90mm x 2.80mm x 1.25mm sop8 5.00mm x 6.20mm x 1.71mm ssop-b8 3.00mm x 6.40mm x 1.35mm msop8 2.90mm x 4.00mm x 0.90mm sop14 8.70mm x 6.20mm x 1.71mm ssop-b14 5.00 mm x 6.40mm x 1.35mm selection guide ba2903f ba2903fv ba2903fvm ba2903sf ba2903sfv ba2903sfvm +125c operation guaranteed input offset voltage (max) ba10339f ba10339fv ba10393f ba2901f ba2901fv ba2901sf ba2901sfv +85c +105c general purpose dual quad 5mv 5mv ba8391g single 7mv high reliability dual 7m quad 7mv 2mv ba2903wf ba2903wfv http://
datasheet www.rohm.com tsz02201-0rfr0g200200-1-2 ?2013 rohm co., ltd. all rights reserved. 2/53 11.dec.2013 rev.003 tsz22111 ? 15 ? 001 ba8391g ba10393f BA10339XX ba2903xxx ba2903sxxx ba2903wxx ba2901xx ba2901sxx 34 2 15 - + out -in +in vee vcc simplified schematic pin configuration ba8391g : ssop5 pin no. pin name 1 -in 2 vee 3 +in 4 out 5 vcc ba10393f, ba2903sf, ba2903f, ba2903wf : sop8 ba2903sfv, ba2903fv, ba2903wfv : ssop-b8 ba2903sfvm,ba2903fvm : msop8 pin no. pin name 1 out1 2 -in1 3 +in1 4 vee 5 +in2 6 -in2 7 out2 8 vcc figure 1. simplified schematic (one channel only) -in vcc +in vee out -+ + - ch1 ch2 8 1 2 3 4 5 6 7 out1 -in1 +in1 vee vcc out2 -in2 +in2 http://
datasheet www.rohm.com tsz02201-0rfr0g200200-1-2 ?2013 rohm co., ltd. all rights reserved. 3/53 11.dec.2013 rev.003 tsz22111 ? 15 ? 001 ba8391g ba10393f BA10339XX ba2903xxx ba2903sxxx ba2903wxx ba2901xx ba2901sxx ba10339f, ba2901sf, ba2901f : sop14 ba10339fv, ba2901sfv, ba2901fv : ssop-b14 package ssop5 sop8 ssop-b8 msop8 sop14 ssop-b14 ba8391g ba10393f ba2903sf ba2903f ba2903wf ba2903sfv ba2903fv ba2903wfv ba2903sfvm ba2903fvm ba10339f ba2901sf ba2901f ba10339fv ba2901sfv ba2901fv ordering information b a x x x x x x x x - x x part number ba8391 ba10393xx BA10339XX ba2901xx ba2901sxx ba2903xx ba2903sxx ba2903wxx package g : ssop5 f : sop8 sop14 fv : ssop-b8 ssop-b14 fvm : msop8 packaging and forming specification e2: embossed tape and reel (sop8/sop14/ssop-b8/ssop-b14) tr: embossed tape and reel (ssop5/msop8) pin no. pin name 1 out2 2 out1 3 vcc 4 -in1 5 +in1 6 -in2 7 +in2 8 -in3 9 +in3 10 -in4 11 +in4 12 vee 13 out4 14 out3 out2 out1 vcc -in1 +in1 -in2 +in2 out3 out4 vee +in4 -in4 +in3 -in3 1 2 3 4 5 6 78 9 10 11 12 13 14 ch1 ch3 ch2 ch4 http://
datasheet www.rohm.com tsz02201-0rfr0g200200-1-2 ?2013 rohm co., ltd. all rights reserved. 4/53 11.dec.2013 rev.003 tsz22111 ? 15 ? 001 ba8391g ba10393f BA10339XX ba2903xxx ba2903sxxx ba2903wxx ba2901xx ba2901sxx line-up topr input offset voltage (max) supply current (typ) package orderable part number -40c to +85c 7mv 0.3ma ssop5 reel of 3000 ba8391g-tr 5mv 0.4ma sop8 reel of 2500 ba10393f-e2 0.8ma sop14 reel of 2500 ba10339f-e2 ssop-b14 reel of 2500 ba10339fv-e2 -40c to +105c 7mv 0.6ma sop8 reel of 2500 ba2903sf-e2 ssop-b8 reel of 2500 ba2903sfv-e2 msop8 reel of 3000 ba2903sfvm-tr 0.8ma sop14 reel of 2500 ba2901sf-e2 ssop-b14 reel of 2500 ba2901sfv-e2 -40c to +125c 0.6ma sop8 reel of 2500 ba2903f-e2 ssop-b8 reel of 2500 ba2903fv-e2 msop8 reel of 3000 ba2903fvm-tr 2mv sop8 reel of 2500 ba2903wf-e2 ssop-b8 reel of 2500 ba2903wfv-e2 7mv 0.8ma sop14 reel of 2500 ba2901f-e2 ssop-b14 reel of 2500 ba2901fv-e2 absolute maximum ratings (ta=25c) parameter symbol rating unit ba8391g supply voltage vcc-vee +36 v power dissipation pd ssop5 0.67 (note1,2) w differential input voltage (note 3) v id +36 v input common-mode voltage range v icm (vee-0.3) to (vee+36) v input current (note 4) i i -10 ma operating supply voltage v opr +2.0 to +36.0 (1.0 to 18.0) v operating temperature range t opr -40 to +85 c storage temperature range t stg -55 to +150 c maximum junction temperature t jmax +150 c (note 1) to use at temperature above ta 25c reduce 5.4mw. (note 2) mounted on a fr4 glass epoxy pcb(70mm70mm1.6mm). (note 3) the voltage difference between inverting input and non-inverting input is the differential input voltage. then input terminal voltage is set to more than vee. (note 4) excessive input current will flow if a differential in put voltage in excess of approximately 0.6v is applied between t he input unless some limiting resistance is used. caution: operating the ic over the absolute maximum ratings may damage the ic. the damage can either be a short circuit between pins or an open circuit between pins and the internal circuitry. therefore, it is important to consider circuit protection measures, such as adding a f use, in case the ic is operated over the absolute maximum ratings. http://
datasheet www.rohm.com tsz02201-0rfr0g200200-1-2 ?2013 rohm co., ltd. all rights reserved. 5/53 11.dec.2013 rev.003 tsz22111 ? 15 ? 001 ba8391g ba10393f BA10339XX ba2903xxx ba2903sxxx ba2903wxx ba2901xx ba2901sxx absolute maximum ratings - continued parameter symbol rating unit ba10393f BA10339XX supply voltage vcc-vee +36 v power dissipation pd sop8 0.62 (note 5,8) - w sop14 - 0.49 (note 6,8) ssop-b14 - 0.70 (note 7,8) differential input voltage (note 9) v id +36 v input common-mode voltage range v icm (vee-0.3) to vcc v input current (note 10) i i -10 ma operating supply voltage v opr +2.0 to +36.0 (1.0 to 18.0) +3.0 to +36.0 (1.5 to 18.0) v operating temperature range t opr -40 to +85 c storage temperature range t stg -55 to +125 c maximum junction temperature t jmax +125 c (note 5) to use at temperature above ta 25c reduce 6.2mw. (note 6) to use at temperature above ta 25c reduce 4.9mw. (note 7) to use at temperature above ta 25c reduce 7.0mw. (note 8) mounted on a fr4 glass epoxy pcb(70mm70mm1.6mm). (note 9) the voltage difference between inverting input and non-inverting input is the differential input voltage. then input terminal voltage is set to more than vee. (note 10) excessive input current will flow if a differential i nput voltage in excess of approximately 0.6v is applied between the input unless some limiting resistance is used. caution: operating the ic over the absolute maximum ratings may damage the ic. the damage can either be a short circuit between pins or an open circuit between pins and the internal circuitry. therefore, it is important to consider circuit protection measures, such as adding a f use, in case the ic is operated over the absolute maximum ratings. parameter symbol rating unit ba2903sxxx ba2901sxx ba2903xxx ba2901xx supply voltage vcc-vee +36 v power dissipation pd sop8 0.78 (note 11,16) - 0.78 (note 11,16) - w ssop-b8 0.69 (note 12,16) - 0.69 (note 12,16) - msop8 0.59 (note 13,16) - 0.59 (note 13,16) - sop14 - 0.61 (note 14,16) - 0.61 (note 14,16) ssop-b14 - 0.87 (note 15,16) - 0.87 (note 15,16) differential input voltage (note 17) v id 36 v input common-mode voltage range v icm (vee-0.3) to (vee+36) v input current (note 18) i i -10 ma operating supply voltage v opr +2.0 to +36.0 (1.0 to 18.0) v operating temperature range t opr -40 to +105 -40 to +125 c storage temperature range t stg -55 to +150 c maximum junction temperature t jmax +150 c (note 11) to use at temperature above ta 25c reduce 6.2mw. (note 12) to use at temperature above ta 25c reduce 5.5mw. (note 13) to use at temperature above ta 25c reduce 4.7mw. (note 14) to use at temperature above ta 25c reduce 4.9mw. (note 15) to use at temperature above ta 25c reduce 7.0mw. (note 16) mounted on a fr4 glass epoxy pcb(70mm70mm1.6mm). (note 17) the voltage difference between inverting input and non-inverting input is the differential input voltage. then input terminal voltage is set to more than vee. (note 18) excessive input current will flow if a differential i nput voltage in excess of approximately 0.6v is applied between the input unless some limiting resistance is used. caution: operating the ic over the absolute maximum ratings may damage the ic. the damage can either be a short circuit between pins or an open circuit between pins and the internal circuitry. therefore, it is important to consider circuit protection measures, such as adding a f use, in case the ic is operated over the absolute maximum ratings. http://
datasheet www.rohm.com tsz02201-0rfr0g200200-1-2 ?2013 rohm co., ltd. all rights reserved. 6/53 11.dec.2013 rev.003 tsz22111 ? 15 ? 001 ba8391g ba10393f BA10339XX ba2903xxx ba2903sxxx ba2903wxx ba2901xx ba2901sxx electrical characteristics ba8391g(unless otherwise specif ied vcc=+5v, vee=0v, ta=25c) parameter symbol temperature range limit unit conditions min typ max input offset voltage (note 19,20) v io 25c - 2 7 mv out=1.4v full range - - 15 vcc=5 to 36v, out=1.4v input offset current (note 19,20) i io 25c - 5 50 na out=1.4v full range - - 200 input bias current (note 20,21) i b 25c - 50 250 na out=1.4v full range - - 500 input common-mode voltage range v icm 25c 0 - vcc-1.5 v - large signal voltage gain a v 25c 25 100 - v/mv vcc=15v, out=1.4 to 11.4v r l =15k ? , v rl =15v 88 100 - db supply current (note 20) i cc 25c - 0.3 0.7 ma out=open full range - - 1.3 out=open, vcc=36v output sink current (note 22) i sink 25c 6 16 - ma +in=0v, -in=1v out=1.5v output saturation voltage (note 20) (low level output voltage) v ol 25c - 150 400 mv +in= 0v, -in=1v i sink =4ma full range - - 700 output leakage current (note 20) (high level output current) i leak 25c - 0.1 - na +in=1v, -in=0v out=5v full range - - 1 a +in=1v, -in=0v out=36v response time t re 25c - 1.3 - s r l =5.1k ? , v rl =5v in=100mv p-p , overdrive=5mv - 0.4 - r l =5.1k ? , v rl =5v, in=ttl logic swing, v ref =1.4v (note 19) absolute value (note 20) full range ta=-40c to +85c (note 21) current direction: si nce first input stage is composed with pnp tr ansistor, input bias cu rrent flows out of ic. (note 22) under high temperatures, please consider the power dissipation when selecting the output current. when the output terminal is continuously shorted th e output current reduces the internal temperature by flushing. http://
datasheet www.rohm.com tsz02201-0rfr0g200200-1-2 ?2013 rohm co., ltd. all rights reserved. 7/53 11.dec.2013 rev.003 tsz22111 ? 15 ? 001 ba8391g ba10393f BA10339XX ba2903xxx ba2903sxxx ba2903wxx ba2901xx ba2901sxx electrical characteristics - continued ba10393f (unless otherwise specified vcc=+5v, vee=0v, ta=25c) parameter symbol temperature range limit unit conditions min typ max input offset voltage (note 23) v io 25c - 1 5 mv out=1.4v input offset current (note 23) i io 25c - 5 50 na out=1.4v input bias current (note 24) i b 25c - 50 250 na out=1.4v input common-mode voltage range v icm 25c 0 - vcc-1.5 v - large signal voltage gain a v 25c 50 200 - v/mv r l =15k ? , vcc=15v, v rl =15v, out=1.4 to 11.4v 94 106 - db supply current i cc 25c - 0.4 1 ma r l = , all comparators output sink current (note 25) i sink 25c 6 16 - ma -in=1v, +in=0v out=1.5v output saturation voltage (low level output voltage) v ol 25c - 250 400 mv -in=1v, +in=0v i sink =4ma output leakage current (high level output current) i leak 25c - 0.1 - a -in=0v, +in=1v out=5v 25c - - 1 a -in=0v, +in=1v out=36v response time t re 25c - 1.3 - s r l =5.1k ? , v rl =5v in=100mv p-p , overdrive=5mv - 0.4 - r l =5.1k ? , v rl =5v, in=ttl logic swing, v ref =1.4v (note 23) absolute value (note 24) current direction: si nce first input stage is composed with pnp tr ansistor, input bias cu rrent flows out of ic. (note 25) under high temperatures, please consider the power dissipation when selecting the output current. when the output terminal is continuously shorted t he output current reduces the internal temperature by flushing. ba10339 xx(unless otherwise specif ied vcc=+5v, vee=0v, ta=25c) parameter symbol temperature range limit unit conditions min typ max input offset voltage (note 26) v io 25c - 1 5 mv out=1.4v input offset current (note 26) i io 25c - 5 50 na out=1.4v input bias current (note 27) i b 25c - 50 250 na out=1.4v input common-mode voltage range v icm 25c 0 - vcc-1.5 v - large signal voltage gain a v 25c 50 200 - v/mv r l =15k ? , vcc=15v v rl =15v, out=1.4 to 11.4v 94 160 - db supply current i cc 25c - 0.8 2 ma r l = , all comparators output sink current (note 28) i sink 25c 6 16 - ma -in=1v, +in=0v out=1.5v output saturation voltage (low level output voltage) v ol 25c - 250 400 mv -in=1v, +in=0v i sink =4ma output leakage current (high level output current) i leak 25c - 0.1 - na -in=0v, +in=1v out=5v 25c - - 1 a -in=0v, +in=1v out=36v response time t re 25c - 1.3 - s r l =5.1k ? , v rl =5v in=100mv p-p , overdrive=5mv - 0.4 - r l =5.1k ? , v rl =5v, in=ttl logic swing, v ref =1.4v (note 26) absolute value (note 27) current direction: si nce first input stage is composed with pnp tr ansistor, input bias cu rrent flows out of ic. (note 28) under high temperatures, please consider the power dissipation when selecting the output current. when the output terminal is continuously shorted t he output current reduces the internal temperature by flushing. http://
datasheet www.rohm.com tsz02201-0rfr0g200200-1-2 ?2013 rohm co., ltd. all rights reserved. 8/53 11.dec.2013 rev.003 tsz22111 ? 15 ? 001 ba8391g ba10393f BA10339XX ba2903xxx ba2903sxxx ba2903wxx ba2901xx ba2901sxx electrical characteristics - continued ba2903xxx, ba2903s xxx(unless otherwise specified vcc=+5v, vee=0v, ta=25c) parameter symbol temperature range limit unit conditions min typ max input offset voltage (note 29,30) v io 25c - 2 7 mv out=1.4v full range - - 15 vcc=5 to 36v, out=1.4v input offset current (note 29,30) i io 25c - 5 50 na out=1.4v full range - - 200 input bias current (note 30,31) i b 25c - 50 250 na out=1.4v full range - - 500 input common-mode voltage range v icm 25c 0 - vcc-1.5 v - large signal voltage gain a v 25c 25 100 - v/mv vcc=15v, out=1.4 to 11.4v r l =15k ? , v rl =15v 88 100 - db supply current (note 30) i cc 25c - 0.6 1 ma out=open full range - - 2.5 out=open, vcc=36v output sink current (note 32) i sink 25c 6 16 - ma +in=0v, -in=1v out=1.5v output saturation voltage (note 30) (low level output voltage) v ol 25c - 150 400 mv +in=0v, -in= 1v i sink =4ma full range - - 700 output leakage current (note 30) (high level output current) i leak 25c - 0.1 - na +in=1v, -in=0v out=5v full range - - 1 a +in=1v, -in=0v out=36v response time t re 25c - 1.3 - s r l =5.1k ? , v rl =5v in=100mv p-p , overdrive=5mv - 0.4 - r l =5.1k ? , v rl =5v, in=ttl logic swing, v ref =1.4v (note 29) absolute value (note 30) ba2903s : full range -40c to +105c, ba2903: full range -40c to +125c (note 31) current direction: si nce first input stage is composed with pnp tr ansistor, input bias cu rrent flows out of ic. (note 32) under high temperatures, please consider the power dissipation when selecting the output current. when the output terminal is continuously shorted t he output current reduces the internal temperature by flushing. http://
datasheet www.rohm.com tsz02201-0rfr0g200200-1-2 ?2013 rohm co., ltd. all rights reserved. 9/53 11.dec.2013 rev.003 tsz22111 ? 15 ? 001 ba8391g ba10393f BA10339XX ba2903xxx ba2903sxxx ba2903wxx ba2901xx ba2901sxx electrical characteristics - continued ba2903wxx (unless otherwise spec ified vcc=+5v, vee=0v, ta=25c) parameter symbol temperature range limit unit conditions min typ max input offset voltage (note 33) v io 25c - 0.5 2 mv out=1.4v input offset current (note 33) i io 25c - 5 50 na out=1.4v input bias current (note 34,35) i b 25c - 50 250 na out=1.4v full range - - 500 input common-mode voltage range v icm 25c 0 - vcc-1.5 v - large signal voltage gain a v 25c 25 100 - v/mv vcc=15v, out=1.4 to 11.4v r l =15k ? , v rl =15v 88 100 - db supply current (note 34) i cc 25c - 0.6 1 ma out=open full range - - 2.5 out=open, vcc=36v output sink current (note 36) i sink 25c 6 16 - ma +in=0v, -in=1v out=1.5v output saturation voltage (note 34) (low level output voltage) v ol 25c - 150 400 mv +in=0v, -in= 1v i sink =4ma full range - - 700 output leakage current (note 34) (high level output current) i leak 25c - 0.1 - na +in=1v, -in=0v out=5v full range - - 1 a +in=1v, -in=0v out=36v response time t re 25c - 1.3 - s r l =5.1k ? , v rl =5v in=100mv p-p , overdrive=5mv - 0.4 - r l =5.1k ? , v rl =5v, in=ttl logic swing, v ref =1.4v (note 33) absolute value (note 34) ba2903w: full range -40c to +125c (note 35) current direction: si nce first input stage is composed with pnp tr ansistor, input bias cu rrent flows out of ic. (note 36) under high temperatures, please consider the power dissipation when selecting the output current. when the output terminal is continuously shorted t he output current reduces the internal temperature by flushing. http://
datasheet www.rohm.com tsz02201-0rfr0g200200-1-2 ?2013 rohm co., ltd. all rights reserved. 10/53 11.dec.2013 rev.003 tsz22111 ? 15 ? 001 ba8391g ba10393f BA10339XX ba2903xxx ba2903sxxx ba2903wxx ba2901xx ba2901sxx electrical characteristics - continued ba2901xx, ba2901s xx(unless otherwise specified vcc=+5v, vee=0v, ta=25c) parameter symbol temperature range limit unit conditions min typ max input offset voltage (note 37,38) v io 25c - 2 7 mv out=1.4v full range - - 15 vcc=5 to 36v, out=1.4v input offset current (note 37,38) i io 25c - 5 50 na out=1.4v full range - - 200 input bias current (note 38,39) i b 25c - 50 250 na out=1.4v full range - - 500 input common-mode voltage range v icm 25c 0 - vcc-1.5 v - large signal voltage gain a v 25c 25 100 - v/mv vcc=15v, out=1.4 to 11.4v r l =15k ? , v rl =15v 88 100 - db supply current (note 38) i cc 25c - 0.8 2 ma out=open full range - - 2.5 out=open, vcc=36v output sink current (note 40) i sink 25c 6 16 - ma +in=0v, v in =1v out=1.5v output saturation voltage (note 38) (low level output voltage) v ol 25c - 150 400 mv +in=0v, -in=1v i sink =4ma full range - - 700 output leakage current (note 38) (high level output current) i leak 25c - 0.1 - na +in=1v, -in=0v out=5v full range - - 1 a +in=1v, -in=0v out=36v response time t re 25c - 1.3 - s r l =5.1k ? , v rl =5v v in =100mv p-p , overdrive=5mv - 0.4 - r l =5.1k ? , v rl =5v, v in =ttl logic swing, v ref =1.4v (note 37) absolute value (note 38) ba2901s full range -40c to 105c ,ba2901 full range -40c to +125c (note 39) current direction : since first input stage is compos ed with pnp transistor, input bias current flows out of ic. (note 40) under high temperatures, please consider the power dissipation when selecting the output current. when the output terminal is continuously shorted the output current reduces the internal temperature by flushing. http://
datasheet www.rohm.com tsz02201-0rfr0g200200-1-2 ?2013 rohm co., ltd. all rights reserved. 11/53 11.dec.2013 rev.003 tsz22111 ? 15 ? 001 ba8391g ba10393f BA10339XX ba2903xxx ba2903sxxx ba2903wxx ba2901xx ba2901sxx description of electrical characteristics described below are descriptions of the rele vant electrical terms used in this datasheet. items and symbols used are also shown. note that item name and symbol and their meaning ma y differ from those on another manufacturer?s document or general document. 1. absolute maximum ratings absolute maximum rating items indicate the condition which must not be exceeded. application of voltage in excess of absolute maximum rating or use out of absolute maximum rated temperature environment may cause deterioration of characteristics. (1) power supply voltage (vcc/vee) indicates the maximum voltage that can be applied between the positive power supply terminal and negative power supply terminal without deterioration or destruct ion of characteristics of internal circuit. (2) differential input voltage (v id ) indicates the maximum voltage that can be applied betw een non-inverting and inverting terminals without damaging the ic. (3) input common-mode voltage range (v icm ) indicates the maximum voltage that can be applied to the non-inverting and inverting terminals without deterioration or destruction of electrical characteristics. input common-mode voltage range of the maximum ratings does not assure normal operation of ic. for normal operation, use the ic within the input common-mode voltage range characteristics. (4) power dissipation (pd) indicates the power that can be consumed by the ic when mo unted on a specific board at t he ambient temperature 25c (normal temperature). as for package product, pd is determi ned by the temperature that can be permitted by the ic in the package (maximum junction temperature) and the thermal resistance of the package. 2. electrical characteristics (1) input offset voltage (v io ) indicates the voltage difference between non-inverting termi nal and inverting terminals. it can be translated into the input voltage difference required for setting the output voltage at 0 v. (2) input offset current (i io ) indicates the difference of input bias current bet ween the non-inverting and inverting terminals. (3) input bias current (i b ) indicates the current that flows into or out of the input terminal. it is defined by the average of input bias currents at the non-inverting and inverting terminals. (4) input common-mode voltage range (v icm ) indicates the input voltage range where ic normally operates. (5) large signal voltage gain (a v ) indicates the amplifying rate (gain) of output voltage against the voltage difference between non-inverting terminal and inverting terminal. it is normally the amplifying rate (gain) with reference to dc voltage. av = (output voltage) / (differential input voltage) (6) supply current (i cc ) indicates the current that flows within the ic under specified no-load conditions. (7) output sink current (i sink ) denotes the maximum current that can be ou tput under specific output conditions. (8) output saturation voltage, low level output voltage (v ol ) signifies the voltage range that can be out put under specific output conditions. (9) output leakage current, high level output current (i leak ) indicates the current that flows into the ic under specific input and output conditions. (10) response time (t re ) response time indicates the delay time between the i nput and output signal is determined by the time difference from the fifty percent of input signal swing to the fifty percent of output signal swing. http://
datasheet www.rohm.com tsz02201-0rfr0g200200-1-2 ?2013 rohm co., ltd. all rights reserved. 12/53 11.dec.2013 rev.003 tsz22111 ? 15 ? 001 ba8391g ba10393f BA10339XX ba2903xxx ba2903sxxx ba2903wxx ba2901xx ba2901sxx typical performance curves ba8391g (*)the above characteristics are measurements of typical sample, they are not guaranteed. 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 -50 -25 0 25 50 75 100 ambient temperature [c] supply current [ma] 0 0.2 0.4 0.6 0.8 0 25 50 75 100 125 ambient temperature [c] power dissipation [w] ba8391g 5v 2v 36v figure 3. supply current vs supply voltage figure 4. supply current vs ambient temperature figure 2. power dissipation vs ambient temperature (derating curve) figure 5. output saturation voltage vs supply voltage (i ol =4ma) 85 0 50 100 150 200 0 10203040 supply voltage [v] output saturation voltage [mv] -40 25 85 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0 10203040 supply voltage [v] supply current [ma] 25 85 -40 http://
datasheet www.rohm.com tsz02201-0rfr0g200200-1-2 ?2013 rohm co., ltd. all rights reserved. 13/53 11.dec.2013 rev.003 tsz22111 ? 15 ? 001 ba8391g ba10393f BA10339XX ba2903xxx ba2903sxxx ba2903wxx ba2901xx ba2901sxx typical performance curves - continued ba8391g (*)the above characteristics are measurements of typical sample, they are not guaranteed. 0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 0 2 4 6 8 10 12 14 16 18 20 output sink current [ma] output saturation voltage [v] -8 -6 -4 -2 0 2 4 6 8 0 10203040 supply voltage [v] input offset voltage [mv] 0 10 20 30 40 -50 -25 0 25 50 75 100 ambient temperature [c] output sink current [ma] 0 50 100 150 200 -50 -25 0 25 50 75 100 ambient temperature [c] output saturation voltage [mv] . 2v 36v 5v 36v 5v 2v -40 25 85 -40 25 85 figure 9. input offset voltage vs supply voltage figure 6. output saturation voltage vs ambient temperature ( i ol =4ma) figure 7. output saturation voltage vs output sink current (vcc=5v) figure 8. output sink current vs ambient temperature (out=1.5v) http://
datasheet www.rohm.com tsz02201-0rfr0g200200-1-2 ?2013 rohm co., ltd. all rights reserved. 14/53 11.dec.2013 rev.003 tsz22111 ? 15 ? 001 ba8391g ba10393f BA10339XX ba2903xxx ba2903sxxx ba2903wxx ba2901xx ba2901sxx typical performance curves - continued ba8391g (*)the above characteristics are measurements of typical sample, they are not guaranteed. -50 -40 -30 -20 -10 0 10 20 30 40 50 0 10203040 supply voltage [v] input offset current [na] 0 20 40 60 80 100 120 140 160 -50 -25 0 25 50 75 100 ambient temperature [c] input bias current [na] 0 20 40 60 80 100 120 140 160 0 10203040 supply voltage [v] input bias current [na] -8 -6 -4 -2 0 2 4 6 8 -50 -25 0 25 50 75 100 ambient temperature [c] input offset voltage [mv] 2v 5v 36v -40 25 85 2v 5v 36v 85 25 -40 figure 10. input offset voltage vs ambient temperature figure 11. input bias current vs supply voltage figure 12. input bias current vs ambient temperature figure 13. input offset current vs supply voltage http://
datasheet www.rohm.com tsz02201-0rfr0g200200-1-2 ?2013 rohm co., ltd. all rights reserved. 15/53 11.dec.2013 rev.003 tsz22111 ? 15 ? 001 ba8391g ba10393f BA10339XX ba2903xxx ba2903sxxx ba2903wxx ba2901xx ba2901sxx typical performance curves - continued ba8391g (*)the above characteristics are measurements of typical sample, they are not guaranteed. 40 60 80 100 120 140 160 010203040 supply voltage [v] common mode rejection ratio [db] 60 70 80 90 100 110 120 130 140 -50 -25 0 25 50 75 100 ambient temperature [c] large signal voltage gain [db] 60 70 80 90 100 110 120 130 140 0 10203040 supply voltage [v] large signal voltage gain [db] -50 -40 -30 -20 -10 0 10 20 30 40 50 -50 -25 0 25 50 75 100 ambient temperature [c] input offset current [na] 5v 36v 2v 85 25 -40 2v 5v 36v -40 25 85 figure 15. large signal voltage gain vs supply voltage figure 14. input offset current vs ambient temperature figure 17. common mode rejection ratio vs supply voltage figure 16. large signal voltage gain vs ambient temperature http://
datasheet www.rohm.com tsz02201-0rfr0g200200-1-2 ?2013 rohm co., ltd. all rights reserved. 16/53 11.dec.2013 rev.003 tsz22111 ? 15 ? 001 ba8391g ba10393f BA10339XX ba2903xxx ba2903sxxx ba2903wxx ba2901xx ba2901sxx typical performance curves - continued ba8391g (*)the above characteristics are measurements of typical sample, they are not guaranteed. 0 1 2 3 4 5 -100-80-60-40-20 0 output drive voltage [mv] response time (low to high) [ s] 60 80 100 120 140 160 180 200 -50 -25 0 25 50 75 100 ambient temperature [c] power supply rejection ratio [db] -6 -4 -2 0 2 4 6 -1012345 input voltage [v] input offset volatge [mv] 0 25 50 75 100 125 150 -50 -25 0 25 50 75 100 ambient temperature [c] common mode rejection ratio [db] 2v 5v 36v -40 25 85 -40 25 85 figure 18. common mode rejection ratio vs ambient temperature figure 20. power supply rejection ratio vs ambient temperature figure 19. input offset voltage - input voltage (vcc=5v) figure 21. response time (low to high) vs over drive voltage (vcc=5v, v rl =5v, r l =5.1k ? ) http://
datasheet www.rohm.com tsz02201-0rfr0g200200-1-2 ?2013 rohm co., ltd. all rights reserved. 17/53 11.dec.2013 rev.003 tsz22111 ? 15 ? 001 ba8391g ba10393f BA10339XX ba2903xxx ba2903sxxx ba2903wxx ba2901xx ba2901sxx typical performance curves - continued ba8391g (*)the above characteristics are measurements of typical sample, they are not guaranteed. 0 1 2 3 4 5 -50 -25 0 25 50 75 100 ambient temperature [c] response time (high to low) [ s] 0 1 2 3 4 5 0 20406080100 output drive voltage [mv] response time (low to high) [ s] 0 1 2 3 4 5 -50 -25 0 25 50 75 100 ambient temperature [c] response time (low to high) [ s] -40 25 85 figure 22. response time (low to high) vs ambient temperature (vcc=5v, v rl =5v, r l =5.1k ? ) figure 24. response time (high to low) vs ambient temperature (vcc=5v, v rl =5v, r l =5.1k ? ) figure 23. response time (high to low) vs over drive voltage (vcc=5v, v rl =5v, r l =5.1k ? ) 5mv overdrive 20mv overdrive 100mv overdrive 5mv overdrive 20mv overdrive 100mv overdrive http://
datasheet www.rohm.com tsz02201-0rfr0g200200-1-2 ?2013 rohm co., ltd. all rights reserved. 18/53 11.dec.2013 rev.003 tsz22111 ? 15 ? 001 ba8391g ba10393f BA10339XX ba2903xxx ba2903sxxx ba2903wxx ba2901xx ba2901sxx typical performance curves - continued ba10393f (*)the above characteristics are measurements of typical sample, they are not guaranteed. 0.0 0.2 0.4 0.6 0.8 1.0 0 25 50 75 100 125 ambient temperature [c] . power dissipation [w] . 0.0 0.2 0.4 0.6 0.8 1.0 -50 -25 0 25 50 75 100 ambient temperature [c] supply current [ma] 0 100 200 300 400 500 0 10203040 supply voltage [v] output saturation voltage [mv] 0.0 0.2 0.4 0.6 0.8 1.0 010203040 supply voltage [v] supply current [ma] ba10393f 2v 36v 5v -40 25 85 25 85 -40 figure 26. supply current vs supply voltage figure 27. supply current vs ambient temperature figure 25. power dissipation vs ambient temperature (derating curve) figure 28. output saturation voltage vs supply voltage (i ol =4ma) 85 http://
datasheet www.rohm.com tsz02201-0rfr0g200200-1-2 ?2013 rohm co., ltd. all rights reserved. 19/53 11.dec.2013 rev.003 tsz22111 ? 15 ? 001 ba8391g ba10393f BA10339XX ba2903xxx ba2903sxxx ba2903wxx ba2901xx ba2901sxx typical performance curves - continued ba10393f (*)the above characteristics are measurements of typical sample, they are not guaranteed. -8 -6 -4 -2 0 2 4 6 8 0 10203040 supply voltage [v] input offset voltage [mv] 0 10 20 30 40 -50 -25 0 25 50 75 100 ambient temperature [c] output sink current [ma] 0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 0 2 4 6 8 101214161820 output sink current [ma] output saturation voltage [v] 0 100 200 300 400 500 -50 -25 0 25 50 75 100 ambient temperature [c] output saturation voltage [mv] 2v 36v 5v -40 25 85 36v 5v 2v -40 25 85 figure 32. input offset voltage vs supply voltage figure 29. output saturation voltage vs ambient temperature ( i ol =4ma) figure 30. output saturation voltage vs output sink current (vcc=5v) figure 31. output sink current vs ambient temperature (out=1.5v) http://
datasheet www.rohm.com tsz02201-0rfr0g200200-1-2 ?2013 rohm co., ltd. all rights reserved. 20/53 11.dec.2013 rev.003 tsz22111 ? 15 ? 001 ba8391g ba10393f BA10339XX ba2903xxx ba2903sxxx ba2903wxx ba2901xx ba2901sxx typical performance curves - continued ba10393f (*)the above characteristics are measurements of typical sample, they are not guaranteed. -50 -40 -30 -20 -10 0 10 20 30 40 50 0 10203040 supply voltage [v] input offset current [na] 0 20 40 60 80 100 120 140 160 -50 -25 0 25 50 75 100 ambient temperature [c] input bias current [na] 0 20 40 60 80 100 120 140 160 0 10203040 supply voltage [v] input bias current [na] -8 -6 -4 -2 0 2 4 6 8 -50 -25 0 25 50 75 100 ambient temperature [c] input offset voltage [mv] 2v 5v 36v -40 25 85 2v 5v 36v 85 25 -40 figure 33. input offset voltage vs ambient temperature figure 34. input bias current vs supply voltage figure 35. input bias current vs ambient temperature figure 36. input offset current vs supply voltage http://
datasheet www.rohm.com tsz02201-0rfr0g200200-1-2 ?2013 rohm co., ltd. all rights reserved. 21/53 11.dec.2013 rev.003 tsz22111 ? 15 ? 001 ba8391g ba10393f BA10339XX ba2903xxx ba2903sxxx ba2903wxx ba2901xx ba2901sxx typical performance curves - continued ba10393f (*)the above characteristics are measurements of typical sample, they are not guaranteed. 40 60 80 100 120 140 160 010203040 supply voltage [v] common mode rejection ratio [db] 60 70 80 90 100 110 120 130 140 -50 -25 0 25 50 75 100 ambient temperature [c] large signal voltage gain [db] 60 70 80 90 100 110 120 130 140 010203040 supply voltage [v] large signal voltage gain [db] -50 -40 -30 -20 -10 0 10 20 30 40 50 -50 -25 0 25 50 75 100 ambient temperature [c] input offset current [na] 2v 5v 36v 25 85 -40 2v 5v 36v -40 25 85 figure 38. large signal voltage gain vs supply voltage figure 37. input offset current vs ambient temperature figure 40. common mode rejection ratio vs supply voltage figure 39. large signal voltage gain vs ambient temperature http://
datasheet www.rohm.com tsz02201-0rfr0g200200-1-2 ?2013 rohm co., ltd. all rights reserved. 22/53 11.dec.2013 rev.003 tsz22111 ? 15 ? 001 ba8391g ba10393f BA10339XX ba2903xxx ba2903sxxx ba2903wxx ba2901xx ba2901sxx typical performance curves - continued ba10393f (*)the above characteristics are measurements of typical sample, they are not guaranteed. 0 1 2 3 4 5 -50-25 0 255075100 ambient temperature [c] response time (high to low) [ s] 0 1 2 3 4 5 -50 -25 0 25 50 75 100 ambient temperature [c] response time (low to high) [ s] 60 70 80 90 100 110 120 130 140 -50 -25 0 25 50 75 100 ambient temperature [c] power supply rejection ratio [db] 60 70 80 90 100 110 120 130 140 -50 -25 0 25 50 75 100 ambient temperature [c] common mode rejection ratio [db] 2v 5v 36v 5mv overdrive 20mv overdrive 100mv overdrive 5mv overdrive 20mv overdrive 100mv overdrive figure 41. common mode rejection ratio vs ambient temperature figure 43. response time (low to high) vs ambient temperature (vcc=5v, v rl =5v, r l =5.1k ? ) figure 42. power supply rejection ratio vs ambient temperature figure 44. response time (high to low) vs ambient temperature (vcc=5v, v rl =5v, r l =5.1k ? ) http://
datasheet www.rohm.com tsz02201-0rfr0g200200-1-2 ?2013 rohm co., ltd. all rights reserved. 23/53 11.dec.2013 rev.003 tsz22111 ? 15 ? 001 ba8391g ba10393f BA10339XX ba2903xxx ba2903sxxx ba2903wxx ba2901xx ba2901sxx typical performance curves - continued BA10339XX (*)the above characteristics are measurements of typical sample, they are not guaranteed. 0 100 200 300 400 500 0 10203040 supply voltage [v] output saturation voltage [mv] 0.0 0.2 0.4 0.6 0.8 1.0 0 25 50 75 100 125 ambient temperature [c] power dissipation [w] . 0.0 0.2 0.4 0.6 0.8 1.0 0 10203040 supply voltage [v] supply current [ma] 0 0.2 0.4 0.6 0.8 1 -50 -25 0 25 50 75 100 ambient temperature [c] supply current [ma] -40 25 85 ba10339fv ba10339f 25 85 -40 2v 36v 5v figure 46. supply current vs supply voltage figure 47. supply current vs ambient temperature figure 45. power dissipation vs ambient temperature (derating curve) figure 48. output saturation voltage vs supply voltage (i ol =4ma) 85 http://
datasheet www.rohm.com tsz02201-0rfr0g200200-1-2 ?2013 rohm co., ltd. all rights reserved. 24/53 11.dec.2013 rev.003 tsz22111 ? 15 ? 001 ba8391g ba10393f BA10339XX ba2903xxx ba2903sxxx ba2903wxx ba2901xx ba2901sxx typical performance curves - continued BA10339XX (*)the above characteristics are measurements of typical sample, they are not guaranteed. -8 -6 -4 -2 0 2 4 6 8 0 10203040 supply voltage [v] input offset voltage [mv] 0 10 20 30 40 -50-25 0 255075100 ambient temperature [c] output sink current [ma] 0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 0 2 4 6 8 10 12 14 16 18 20 output sink current [ma] output saturation voltage [v] 0 100 200 300 400 500 -50 -25 0 25 50 75 100 ambient temperature [c] output saturation voltage [mv] 2v 36v 5v -40 25 85 36v 3v 5v -40 25 85 figure 52. input offset voltage vs supply voltage figure 49. output saturation voltage vs ambient temperature ( i ol =4ma) figure 50. output saturation voltage vs output sink current (vcc=5v) figure 51. output sink current vs ambient temperature (out=1.5v) http://
datasheet www.rohm.com tsz02201-0rfr0g200200-1-2 ?2013 rohm co., ltd. all rights reserved. 25/53 11.dec.2013 rev.003 tsz22111 ? 15 ? 001 ba8391g ba10393f BA10339XX ba2903xxx ba2903sxxx ba2903wxx ba2901xx ba2901sxx typical performance curves - continued BA10339XX (*)the above characteristics are measurements of typical sample, they are not guaranteed. -50 -40 -30 -20 -10 0 10 20 30 40 50 010203040 supply voltage [v] input offset current [na] 0 10 20 30 40 50 -50 -25 0 25 50 75 100 ambient temperature [c] input bias current [na] 0 10 20 30 40 50 0 10203040 supply voltage [v] input bias current [na] -8 -6 -4 -2 0 2 4 6 8 010203040 supply voltage [v] input offset voltage [mv] 3v 5v 36v -40 25 85 3v 5v 36v 85 25 -40 figure 53. input offset voltage vs ambient temperature figure 54. input bias current vs supply voltage figure 55. input bias current vs ambient temperature figure 56. input offset current vs supply voltage http://
datasheet www.rohm.com tsz02201-0rfr0g200200-1-2 ?2013 rohm co., ltd. all rights reserved. 26/53 11.dec.2013 rev.003 tsz22111 ? 15 ? 001 ba8391g ba10393f BA10339XX ba2903xxx ba2903sxxx ba2903wxx ba2901xx ba2901sxx typical performance curves - continued BA10339XX (*)the above characteristics are measurements of typical sample, they are not guaranteed. 60 70 80 90 100 110 120 130 140 010203040 supply voltage [v] large signal voltage gain [db] -50 -40 -30 -20 -10 0 10 20 30 40 50 -50 -25 0 25 50 75 100 ambient temperature [c] input offset current [na] 40 60 80 100 120 140 160 0 10203040 supply voltage [v] common mode rejection ratio [db] 60 70 80 90 100 110 120 130 140 -50 -25 0 25 50 75 100 ambient temperature [c] large signal voltage gain [db] 3v 5v 36v 25 85 -40 3v 5v 36v -40 25 85 figure 58. large signal voltage gain vs supply voltage figure 57. input offset current vs ambient temperature figure 60. common mode rejection ratio vs supply voltage figure 59. large signal voltage gain vs ambient temperature http://
datasheet www.rohm.com tsz02201-0rfr0g200200-1-2 ?2013 rohm co., ltd. all rights reserved. 27/53 11.dec.2013 rev.003 tsz22111 ? 15 ? 001 ba8391g ba10393f BA10339XX ba2903xxx ba2903sxxx ba2903wxx ba2901xx ba2901sxx typical performance curves - continued BA10339XX (*)the above characteristics are measurements of typical sample, they are not guaranteed. 0 1 2 3 4 5 -50 -25 0 25 50 75 100 ambient temperature [c] response time (high to low) [ s] 0 1 2 3 4 5 -50 -25 0 25 50 75 100 ambient temperature [c] response time (low to high) [ s] 60 70 80 90 100 110 120 130 140 -50 -25 0 25 50 75 100 ambient temperature [c] power supply rejection ratio [db] 0 25 50 75 100 125 150 -50-25 0 255075100 ambient temperature [c] common mode rejection ratio [db] 3v 5v 36v 5mv overdrive 20mv overdrive 100mv overdrive 5mv overdrive 20mv overdrive 100mv overdrive figure 61. common mode rejection ratio vs ambient temperature figure 63. response time (low to high) vs ambient temperature (vcc=5v, v rl =5v, r l =5.1k ? ) figure 62. power supply rejection ratio vs ambient temperature figure 64. response time (high to low) vs ambient temperature (vcc=5v, v rl =5v, r l =5.1k ? ) http://
datasheet www.rohm.com tsz02201-0rfr0g200200-1-2 ?2013 rohm co., ltd. all rights reserved. 28/53 11.dec.2013 rev.003 tsz22111 ? 15 ? 001 ba8391g ba10393f BA10339XX ba2903xxx ba2903sxxx ba2903wxx ba2901xx ba2901sxx typical performance curves - continued ba2903xxx, ba2903sxxx, ba2903wxx (*)the above characteristics are measurements of typical sample, they are not guaranteed. ba2903 -40c to 125c ba2903s -40c to 105c ba2903w -40c to 125c 0.0 0.2 0.4 0.6 0.8 1.0 0 255075100125150 ambient temperature [c] power dissipation [mw] . 0 50 100 150 200 0 10203040 supply voltage [v] output saturation voltage [mv] 0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 -50 -25 0 25 50 75 100 125 150 ambient temperature [c] supply current [ma] 0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 0 10203040 supply voltage [v] supply current [ma] 25 125 -40 2v 5v ba2903fvm ba2 903s fvm ba2903f ba2903sf -40 25 125 105 105 105 ba2903fv ba2903sfv 36v figure 66. supply current vs supply voltage figure 67. supply current vs ambient temperature figure 65. power dissipation vs ambient temperature (derating curve) (refer to the following operating temperature) figure 68. output saturation voltage vs supply voltage (i ol =4ma) http://
datasheet www.rohm.com tsz02201-0rfr0g200200-1-2 ?2013 rohm co., ltd. all rights reserved. 29/53 11.dec.2013 rev.003 tsz22111 ? 15 ? 001 ba8391g ba10393f BA10339XX ba2903xxx ba2903sxxx ba2903wxx ba2901xx ba2901sxx typical performance curves - continued ba2903xxx, ba2903sxxx, ba2903wxx (*)the above characteristics are measurements of typical sample, they are not guaranteed. ba2903 -40c to 125c ba2903s -40c to 105c ba2903w -40c to 125c 0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 0 2 4 6 8 101214161820 output sink current [ma] output saturation voltage [v] -8 -6 -4 -2 0 2 4 6 8 010203040 supply voltage [v] input offset voltage [mv] 0 10 20 30 40 -50 -25 0 25 50 75 100 125 150 ambient temperature [c] output sink current [ma] 0 50 100 150 200 -50 -25 0 25 50 75 100 125 150 ambient temperature [c] output saturation voltage [mv] 36v 5v -40 25 125 36v 5v 2v -40 25 125 105 2v 105 figure 72. input offset voltage vs supply voltage figure 69. output saturation voltage vs ambient temperature ( i ol =4ma) figure 70. output saturation voltage vs output sink current (vcc=5v) figure 71. output sink current vs ambient temperature (out=1.5v) http://
datasheet www.rohm.com tsz02201-0rfr0g200200-1-2 ?2013 rohm co., ltd. all rights reserved. 30/53 11.dec.2013 rev.003 tsz22111 ? 15 ? 001 ba8391g ba10393f BA10339XX ba2903xxx ba2903sxxx ba2903wxx ba2901xx ba2901sxx typical performance curves - continued ba2903xxx, ba2903sxxx, ba2903wxx (*)the above characteristics are measurements of typical sample, they are not guaranteed. ba2903 -40c to 125c ba2903s -40c to 105c ba2903w -40c to 125c 0 20 40 60 80 100 120 140 160 -50 -25 0 25 50 75 100 125 150 ambient temperature [c] input bias current [na] -50 -40 -30 -20 -10 0 10 20 30 40 50 0 10203040 supply voltage [v] input offset current [na] 0 20 40 60 80 100 120 140 160 0 5 10 15 20 25 30 35 supply voltage [v] input bias current [na] -8 -6 -4 -2 0 2 4 6 8 -50 -25 0 25 50 75 100 125 150 ambient temperature [c] input offset voltage [mv] 2v 5v 36v 125 25 -40 -40 25 125 2v 5v 105 105 36v figure 73. input offset voltage vs ambient temperature figure 74. input bias current vs supply voltage figure 75. input bias current vs ambient temperature figure 76. input offset current vs supply voltage http://
datasheet www.rohm.com tsz02201-0rfr0g200200-1-2 ?2013 rohm co., ltd. all rights reserved. 31/53 11.dec.2013 rev.003 tsz22111 ? 15 ? 001 ba8391g ba10393f BA10339XX ba2903xxx ba2903sxxx ba2903wxx ba2901xx ba2901sxx typical performance curves - continued ba2903xxx, ba2903sxxx, ba2903wxx (*)the above characteristics are measurements of typical sample, they are not guaranteed. ba2903 -40c to 125c ba2903s -40c to 105c ba2903w -40c to 125c 40 60 80 100 120 140 160 0 10203040 supply voltage [v] common mode rejection ratio [db] 60 70 80 90 100 110 120 130 140 -50 -25 0 25 50 75 100 125 150 ambient temperature [c] large signal voltage gain [db] 60 70 80 90 100 110 120 130 140 0 10203040 supply voltage [v] large signal voltage gain [db] -50 -40 -30 -20 -10 0 10 20 30 40 50 -50 -25 0 25 50 75 100 125 150 ambient temperature [c] input offset current [na] -40 25 125 2v 5v 36v 25 125 -40 15v 5v 36v 105 105 figure 78. large signal voltage gain vs supply voltage figure 77. input offset current vs ambient temperature figure 80. common mode rejection ratio vs supply voltage figure 79. large signal voltage gain vs ambient temperature http://
datasheet www.rohm.com tsz02201-0rfr0g200200-1-2 ?2013 rohm co., ltd. all rights reserved. 32/53 11.dec.2013 rev.003 tsz22111 ? 15 ? 001 ba8391g ba10393f BA10339XX ba2903xxx ba2903sxxx ba2903wxx ba2901xx ba2901sxx typical performance curves - continued ba2903xxx, ba2903sxxx, ba2903wxx (*)the above characteristics are measurements of typical sample, they are not guaranteed. ba2903 -40c to 125c ba2903s -40c to 105c ba2903w -40c to 125c 0 1 2 3 4 5 -100 -80 -60 -40 -20 0 over drive voltage [v] response time (low to high) [ s] 60 80 100 120 140 160 180 200 -50 -25 0 25 50 75 100 125 150 ambient temperature [c] power supply rejection ratio [db] -6 -4 -2 0 2 4 6 -1012345 input voltage [v] input offset voltage [mv] 0 25 50 75 100 125 150 -50 -25 0 25 50 75 100 125 150 ambient temperature [c] common mode rejection ratio [db] 2v 5v 36v -40 25 125 125 25 -40 105 105 figure 81. common mode rejection ratio vs ambient temperature figure 83. power supply rejection ratio vs ambient temperature figure 82. input offset voltage - input voltage (vcc=5v) figure 84. response time (low to high) vs over drive voltage (vcc=5v, v rl =5v, r l =5.1k ? ) http://
datasheet www.rohm.com tsz02201-0rfr0g200200-1-2 ?2013 rohm co., ltd. all rights reserved. 33/53 11.dec.2013 rev.003 tsz22111 ? 15 ? 001 ba8391g ba10393f BA10339XX ba2903xxx ba2903sxxx ba2903wxx ba2901xx ba2901sxx typical performance curves - continued ba2903xxx, ba2903sxxx, ba2903wxx (*)the above characteristics are measurements of typical sample, they are not guaranteed. ba2903 -40c to 125c ba2903s -40c to 105c ba2903w -40c to 125c 0 1 2 3 4 5 -50 -25 0 25 50 75 100 125 150 ambient temperature [c] response time (high to low) [ s] 0 1 2 3 4 5 0 20406080100 over drive voltage [v] response time (high to low) [ s] 0 1 2 3 4 5 -50 -25 0 25 50 75 100 125 150 ambient temperature [c] response time (low to high) [ s] 5mv overdrive 20mv overdrive 100mv overdrive 125 25 -40 5mv overdrive 20mv overdrive 100mv overdrive 105 figure 85. response time (low to high) vs ambient temperature (vcc=5v, v rl =5v, r l =5.1k ? ) figure 87. response time (high to low) vs ambient temperature (vcc=5v, v rl =5v, r l =5.1k ? ) figure 86. response time (high to low) vs over drive voltage (vcc=5v, v rl =5v, r l =5.1k ? ) http://
datasheet www.rohm.com tsz02201-0rfr0g200200-1-2 ?2013 rohm co., ltd. all rights reserved. 34/53 11.dec.2013 rev.003 tsz22111 ? 15 ? 001 ba8391g ba10393f BA10339XX ba2903xxx ba2903sxxx ba2903wxx ba2901xx ba2901sxx typical performance curves - continued ba2901xx, ba2901sxx (*)the above characteristics are measurements of typical sample, they are not guaranteed. ba2901 -40c to 125c ba2901s -40c to 105c 0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 0 10203040 supply voltage [v] supply current [ma] 0.0 0.2 0.4 0.6 0.8 1.0 0 25 50 75 100 125 150 ambient temperature [c] power dissipation [w] ba2901fv ba2901sfv ba2901f ba2901sf 105 -40 25 125 105 0 50 100 150 200 0 10203040 supply voltage [v] output saturation voltage [mv] -40 25 125 105 figure 89. supply current vs supply voltage figure 90. supply current vs ambient temperature figure 88. power dissipation vs ambient temperature (derating curve) (refer to the following operating temperature) figure 91. output saturation voltage vs supply voltage (i ol =4ma) 0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 -50 -25 0 25 50 75 100 125 150 ambient temperature [c] supply current [ma] 2v 5v 36v http://
datasheet www.rohm.com tsz02201-0rfr0g200200-1-2 ?2013 rohm co., ltd. all rights reserved. 35/53 11.dec.2013 rev.003 tsz22111 ? 15 ? 001 ba8391g ba10393f BA10339XX ba2903xxx ba2903sxxx ba2903wxx ba2901xx ba2901sxx typical performance curves - continued ba2901xx, ba2901sxx (*)the above characteristics are measurements of typical sample, they are not guaranteed. ba2901 -40c to 125c ba2901s -40c to 105c 0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 0 2 4 6 8 101214161820 output sink current [ma] output saturation voltage [v] -8 -6 -4 -2 0 2 4 6 8 0 10203040 supply voltage [v] input offset voltage [mv] 0 10 20 30 40 -50 -25 0 25 50 75 100 125 150 ambient temperature [c] output sink current [ma] 0 50 100 150 200 -50 -25 0 25 50 75 100 125 150 ambient temperature [c] output saturation voltage [mv] 36v 5v -40 25 125 36v 5v 2v -40 25 125 105 2v 105 figure 95. input offset voltage vs supply voltage figure 92. output saturation voltage vs ambient temperature ( i ol =4ma) figure 93. output saturation voltage vs output sink current (vcc=5v) figure 94. output sink current vs ambient temperature (out=1.5v) http://
datasheet www.rohm.com tsz02201-0rfr0g200200-1-2 ?2013 rohm co., ltd. all rights reserved. 36/53 11.dec.2013 rev.003 tsz22111 ? 15 ? 001 ba8391g ba10393f BA10339XX ba2903xxx ba2903sxxx ba2903wxx ba2901xx ba2901sxx typical performance curves - continued ba2901xx, ba2901sxx (*)the above characteristics are measurements of typical sample, they are not guaranteed. ba2901 -40c to 125c ba2901s -40c to 105c 0 20 40 60 80 100 120 140 160 -50 -25 0 25 50 75 100 125 150 ambient temperature [c] input bias current [na] -50 -40 -30 -20 -10 0 10 20 30 40 50 0 10203040 supply voltage [v] input offset current [na] 0 20 40 60 80 100 120 140 160 0 10203040 supply voltage [v] input bias current [na] -8 -6 -4 -2 0 2 4 6 8 -50 -25 0 25 50 75 100 125 150 ambient temperature [c] input offset voltage [mv] 2v 5v 36v 125 25 -40 -40 25 125 2v 5v 105 105 36v figure 96. input offset voltage vs ambient temperature figure 97. input bias current vs supply voltage figure 98. input bias current vs ambient temperature figure 99. input offset current vs supply voltage http://
datasheet www.rohm.com tsz02201-0rfr0g200200-1-2 ?2013 rohm co., ltd. all rights reserved. 37/53 11.dec.2013 rev.003 tsz22111 ? 15 ? 001 ba8391g ba10393f BA10339XX ba2903xxx ba2903sxxx ba2903wxx ba2901xx ba2901sxx typical performance curves - continued ba2901xx, ba2901sxx (*)the above characteristics are measurements of typical sample, they are not guaranteed. ba2901 -40c to 125c ba2901s -40c to 105c 40 60 80 100 120 140 160 0 10203040 supply voltage [v] common mode rejection ratio [db] 60 70 80 90 100 110 120 130 140 -50 -25 0 25 50 75 100 125 150 ambient temperature [c] large signal voltage gain [db] 60 70 80 90 100 110 120 130 140 0 10203040 supply voltage [v] large signal voltage gain [db] -50 -40 -30 -20 -10 0 10 20 30 40 50 -50 -25 0 25 50 75 100 125 150 ambient temperature [c] input offset current [na] -40 25 125 2v 5v 36v 25 125 -40 15v 5v 36v 105 105 figure 101. large signal voltage gain vs supply voltage figure 100. input offset current vs ambient temperature figure 103. common mode rejection ratio vs supply voltage figure 102. large signal voltage gain vs ambient temperature http://
datasheet www.rohm.com tsz02201-0rfr0g200200-1-2 ?2013 rohm co., ltd. all rights reserved. 38/53 11.dec.2013 rev.003 tsz22111 ? 15 ? 001 ba8391g ba10393f BA10339XX ba2903xxx ba2903sxxx ba2903wxx ba2901xx ba2901sxx typical performance curves - continued ba2901xx, ba2901sxx (*)the above characteristics are measurements of typical sample, they are not guaranteed. ba2901 -40c to 125c ba2901s -40c to 105c 0 1 2 3 4 5 -100 -80 -60 -40 -20 0 over drive voltage [v] response time (low to high) [ s] 60 80 100 120 140 160 180 200 -50 -25 0 25 50 75 100 125 150 ambient temperature [c] power supply rejection ratio [db] -6 -4 -2 0 2 4 6 -1012345 input voltage [v] input offset voltage [mv] 0 25 50 75 100 125 150 -50 -25 0 25 50 75 100 125 150 ambient temperature [c] common mode rejection ratio [db] 2v 5v 36v -40 25 125 125 25 -40 105 105 figure 104. common mode rejection ratio vs ambient temperature figure 106. power supply rejection ratio vs ambient temperature figure 105. input offset voltage - input voltage (vcc=5v) figure 107. response time (low to high) vs over drive voltage (vcc=5v, v rl =5v, r l =5.1k ? ) http://
datasheet www.rohm.com tsz02201-0rfr0g200200-1-2 ?2013 rohm co., ltd. all rights reserved. 39/53 11.dec.2013 rev.003 tsz22111 ? 15 ? 001 ba8391g ba10393f BA10339XX ba2903xxx ba2903sxxx ba2903wxx ba2901xx ba2901sxx typical performance curves - continued ba2901xx, ba2901sxx (*)the above characteristics are measurements of typical sample, they are not guaranteed. ba2901 -40c to 125c ba2901s -40c to 105c 0 1 2 3 4 5 0 20406080100 over drive voltage [v] response time (high to low) [ s] 0 1 2 3 4 5 -50 -25 0 25 50 75 100 125 150 ambient temperature [c] response time (high to low) [ s] 0 1 2 3 4 5 -50 -25 0 25 50 75 100 125 150 ambient temperature [c] response time (low to high) [ s] 5mv overdrive 20mv overdrive 100mv overdrive 125 25 -40 5mv overdrive 20mv overdrive 100mv overdrive 105 figure 108. response time (low to high) vs ambient temperature (vcc=5v, v rl =5v, r l =5.1k ? ) figure 110. response time (high to low) vs ambient temperature (vcc=5v, v rl =5v, r l =5.1k ? ) figure 109. response time (high to low) vs over drive voltage (vcc=5v, v rl =5v, r l =5.1k ? ) http://
datasheet www.rohm.com tsz02201-0rfr0g200200-1-2 ?2013 rohm co., ltd. all rights reserved. 40/53 11.dec.2013 rev.003 tsz22111 ? 15 ? 001 ba8391g ba10393f BA10339XX ba2903xxx ba2903sxxx ba2903wxx ba2901xx ba2901sxx application information null method condition for test circuit1 vcc, vee, ek, v icm unit : v, vrl=vcc parameter v f s1 s2 s3 ba10393 / ba10339 ba8391 / ba2903 / ba2901 calculation vcc vee ek v icm vcc vee ek v icm input offset voltage v f1 on on on 5 0 -1.4 0 5 to 36 0 -1.4 0 1 input offset current v f2 off off on 5 0 -1.4 0 5 0 -1.4 0 2 input bias current v f3 off on on 5 0 -1.4 0 5 0 -1.4 0 3 v f4 on off 5 0 -1.4 0 5 0 -1.4 0 large signal voltage gain v f5 on on on 15 0 -1.4 0 15 0 -1.4 0 4 v f6 15 0 -11.4 0 15 0 -11.4 0 - calculation - 1. input offset voltage (v io ) 2. input offset current (i io ) 3. input bias current (i b ) 4. large signal voltage gain (a v ) figure 111. test circuit1 (one channel only) v io |v f1 | = 1+r f /r s [v] |v f5 -v f6 | a v = ek (1+r f /r s ) [db] 20log = i b |v f4 -v f3 | 2 r i (1+r f /r s ) [a] i io |v f2 -v f1 | r i (1+r f /r s ) [a] = vf rl 0.1f 500k 500k rf=50k rs=50 ri=10k ek null dut v sw1 sw2 vicm 1000pf sw3 vcc vee -15v +15v ri=10k rs=50 50k http://
datasheet www.rohm.com tsz02201-0rfr0g200200-1-2 ?2013 rohm co., ltd. all rights reserved. 41/53 11.dec.2013 rev.003 tsz22111 ? 15 ? 001 ba8391g ba10393f BA10339XX ba2903xxx ba2903sxxx ba2903wxx ba2901xx ba2901sxx sw2 sw5 a -in +in rl vcc vee sw4 sw3 sw6 sw7 a v out sw1 switch condition for test circuit 2 sw no. sw 1 sw 2 sw 3 sw 4 sw 5 sw 6 sw 7 supply current off off off off off off off output sink current vol=1.5v off on on off off off on saturation voltage iol=4ma off on on off on on off output leakage current voh=36v off on on off off off on response time r l =5.1k ? , v rl =5v on off on on off off off figure 112. test circuit 2 (one channel only) figure 113. response time overdrive voltag e v ref in t re ( low to hig h) out 0v vcc v ref in out input wave vcc/2 over drive voltag e input wave output wave output wave t re (hig h to low) 0v vcc vcc/2 http://
datasheet www.rohm.com tsz02201-0rfr0g200200-1-2 ?2013 rohm co., ltd. all rights reserved. 42/53 11.dec.2013 rev.003 tsz22111 ? 15 ? 001 ba8391g ba10393f BA10339XX ba2903xxx ba2903sxxx ba2903wxx ba2901xx ba2901sxx power dissipation power dissipation (total loss) indicates the power that can be consumed by ic at ta=25 c (normal temperature).ic is heated when it consumed power, and the temperature of ic chip becomes higher than ambient temperature. the temperature that can be accepted by ic chip depends on ci rcuit configuration, manufacturing process, and consumable power is limited. power dissipation is determined by the tem perature allowed in ic chip (maximum junction temperature) and thermal resistance of package (heat dissipation capability). the maximum junction temperature is typically equal to the maximum value in the storage temperature range. heat generat ed by consumed power of ic radiates from the mold resin or lead frame of the package. the parameter which indicates this heat dissipation capability (hardness of heat release)is called thermal resistance, represented by the symbol ja c/w.the temperature of ic inside the package can be estimated by this thermal resistance. figure 114 (a) shows the model of thermal resistance of the package. thermal resistance ja, ambient temperature ta, maximum junction temperature tjmax, and power dissipation pd can be calculated by the equation below: ja = (tj-ta) / pd c/w ????? ( ) derating curve in figure 114 (b) indicates power that can be consumed by ic with reference to ambient temperature. power that can be consumed by ic begins to attenuate at certain ambient temperature. this gradient is determined by thermal resistance ja. thermal resistance ja depends on chip size, power consumption, package, ambient temperature, package condition, wind velocity, etc even when the same of package is used. thermal reduction curve indicates a reference value measured at a specified condition. figure 115 (c) to (g ) shows a derating curve for an example of ba8391, ba10393, ba10339, ba2903s, ba2903, ba2903w, ba2901s, and ba2901. (note 41) (note 42) (note 43) (note 44) (note 45) (note 46) (note 47) (note 48) (note 49) unit 5.4 6.2 7.0 4.9 6.2 5.5 4.7 7.0 4.9 mw/ when using the unit above ta=25 , subtract the value above per degree . permissible dissipation is the value w hen fr4 glass epoxy board 70mm 70mm 1.6mm (cooper foil area below 3%) is mounted. ba2901 -40c to 125c ba2901s -40c to 105c, ba2901 -40c to 125c ba2901s -40c to 105c 0.0 0.2 0.4 0.6 0.8 1.0 0 25 50 75 100 125 150 ambient temperature [c] power dissipation [w] 0.0 0.2 0.4 0.6 0.8 1.0 0 25 50 75 100 125 150 ambient temperature [c] power dissipation [w] 0.0 0.2 0.4 0.6 0.8 1.0 0 25 50 75 100 125 ambient temperature [c] power dissipation [w] 0.0 0.2 0.4 0.6 0.8 1.0 0 25 50 75 100 125 ambient temperature [c] power dissipation [w] 0.0 0.2 0.4 0.6 0.8 1.0 0 25 50 75 100 125 ambient temperature [c] power dissipation [w] (a) thermal resistance figure 114. thermal resistance and derating curve figure 115. derating curve ?? ta [ ] ??? tj [ ] M p [w] ja=(tjmax-ta)/pd c/w 0 50 75 100 125 150 25 p1 p2 pd (max) lsi M [w] ' ja2 ' ja1 tj ' (m ax ) ja2 < ja1 ?? ta [ ] ja2 ja1 tj (m ax ) power dissipation of lsi [w] a mbient temperature ta [ ] ambient temperature ta [ ] chip surface temperature tj [ ] power dissipation pd [w] (f)ba2903xxx ba2903sxxx (g)ba2901xxx ba2901sxxx (d)ba10393f (e)BA10339XX ba10393f (note 42) ba10339fv (note 43) ba10339f (note 44) ba2903f (note 45) ba2903wf (note 45) ba2903sf (note 45) ba2903fv (note 46) ba2903wfv (note 46) ba2903sfv (note 46) ba2903fvm (note 47) ba2903sfvm (note 47) ba2901fv (note 48) ba2901sfv (note 48) ba2901f (note 49) ba2901sf (note 49) (c)ba8391g ba8391g (note 41) (b) derating curve http://
datasheet www.rohm.com tsz02201-0rfr0g200200-1-2 ?2013 rohm co., ltd. all rights reserved. 43/53 11.dec.2013 rev.003 tsz22111 ? 15 ? 001 ba8391g ba10393f BA10339XX ba2903xxx ba2903sxxx ba2903wxx ba2901xx ba2901sxx example of circuit reference voltage is v in- while input voltage is bigger than reference voltage, output voltage is high. while input voltage is smaller than reference voltage, output voltage is low. reference voltage is v in+ while input voltage is smaller than reference voltage, output voltage is high. while input voltage is bigger than reference voltage, output voltage is low. reference voltage v ref in vcc vee vrl rl out + - + - v ref vee vcc vrl rl reference voltage in time v ref out time high low time v ref low high time in out http://
datasheet www.rohm.com tsz02201-0rfr0g200200-1-2 ?2013 rohm co., ltd. all rights reserved. 44/53 11.dec.2013 rev.003 tsz22111 ? 15 ? 001 ba8391g ba10393f BA10339XX ba2903xxx ba2903sxxx ba2903wxx ba2901xx ba2901sxx operational notes 1. reverse connection of power supply connecting the power supply in reverse polarity can damage the ic. take precautions against reverse polarity when connecting the power supply, such as mounting an external diode between the power supply and the ic?s power supply terminals. 2. power supply lines design the pcb layout pattern to provide low impedance ground and supply lines. separate the ground and supply lines of the digital and analog blocks to prevent noise in t he ground and supply lines of the digital block from affecting the analog block. furthermore, connect a capacitor to ground at all power supply pins. consider the effect of temperature and aging on the capacitance value when using electrolytic capacitors. 3. ground voltage ensure that no pins are at a voltage below that of the ground pin at any time, even during transient condition. 4. ground wiring pattern when using both small-signal and large- current gnd traces, the two ground traces should be routed separately but connected to a single ground at the reference point of the application board to avoid fluctuations in the small-signal ground caused by large currents. also ensure that the gnd tr aces of external components do not cause variations on the gnd voltage. the power supply and ground lines must be as short and thick as possible to reduce line impedance. 5. thermal consideration should by any chance the power dissipation rating be exceeded, the rise in temperature of the chip may result in deterioration of the properties of the chip. the absolute maxi mum rating of the pd stated in this specification is when the ic is mounted on a 70mm x 70mm x 1.6mm glass epoxy board. in case of exceeding this absolute maximum rating, increase the board size and copper area to prevent exceeding the pd rating. 6. recommended operating conditions these conditions represent a range within which the expect ed characteristics of the ic can be approximately obtained. the electrical characteristics are guaranteed under the conditions of each parameter. 7. inrush current when power is first supplied to the ic, it is possible that the internal logic may be unstable and inrush current may flow instantaneously due to the internal powering sequence and delays, especially if the ic has more than one power supply. therefore, give special consideration to power coupling capa citance, power wiring, width of gnd wiring, and routing of connections. 8. operation under strong electromagnetic field operating the ic in the presence of a strong electromagnetic field may cause the ic to malfunction. 9. testing on application boards when testing the ic on an application board, connecting a ca pacitor directly to a low-impedance output pin may subject the ic to stress. always discharge capacitors completely after each process or step. the ic?s power supply should always be turned off completely before connecting or removi ng it from the test setup during the inspection process. to prevent damage from static discharge, ground the ic during assembly and use similar precautions during transport and storage. 10. inter-pin short and mounting errors ensure that the direction and position are correct when mounting the ic on the pcb. incorrect mounting may result in damaging the ic. avoid nearby pins being shorted to each other especially to ground. inter-pin shorts could be due to many reasons such as metal particles, water droplets (in very humid environment) and unintentional solder bridge deposited in between pins during assembly to name a few. http://
datasheet www.rohm.com tsz02201-0rfr0g200200-1-2 ?2013 rohm co., ltd. all rights reserved. 45/53 11.dec.2013 rev.003 tsz22111 ? 15 ? 001 ba8391g ba10393f BA10339XX ba2903xxx ba2903sxxx ba2903wxx ba2901xx ba2901sxx + - vcc vee open v icm operational notes ? continued 11. regarding input pins of the ic this monolithic ic contains p+ isolation and p substrat e layers between adjacent elements in order to keep them isolated. p-n junctions are formed at the intersection of th e p layers with the n layers of other elements, creating a parasitic diode or transistor. for example (refer to figure below): when gnd > pin a and gnd > pin b, the p-n junction operates as a parasitic diode. when gnd > pin b, the p-n junction op erates as a parasitic transistor. parasitic diodes inevitably occur in the structure of the ic. the operation of parasitic diodes can result in mutual interference among circuits, operational faults, or physical damage. therefore, conditions that cause these diodes to operate, such as applying a voltage lower than the gnd voltage to an input pin (and thus to the p substrate) should be avoided. nn p + p nn p + p substrate parasitic element gnd n p + nn p + n p p substrate gnd gnd parasitic element pin a pin a pin b pin b bc e parasitic element gnd parasitic element or transistor parasitic element c b e transistor (npn) resistor figure 116. example of monolithic ic structure 12. unused circuits when there are unused circuits it is recommended that they be connected as in figure 117, setting the non-inverting input terminal to a potential within the in-phase input voltage range (v icr ). figure 117. disable circuit example 13. input terminal voltage (ba8391g / ba2903xxxx / ba2901xxx) applying vee + 36v to the input terminal is possible without causing deterioration of the electrical characteristics or destruction, irrespective of the supply voltage. however, this does not ensure normal circuit operation. please note that the circuit operates normally only when the input voltage is within the common mode input voltage range of the electric characteristics. 14. power supply (signal / dual) the comparators when the specified voltage supplied is between vcc and vee. therefore, the single supply comparators can be used as a dual supply comparators as well. 15. terminal short-circuits when the output and vcc terminals are shorted, excessive output current may flow, resulting in undue heat generation and, subsequently, destruction. 16. ic handling applying mechanical stress to the ic by deflecting or bending the board may cause fluctuations in the electrical characteristics due to piezo resistance effects. pl ease k eep this potential in v icm http://
datasheet www.rohm.com tsz02201-0rfr0g200200-1-2 ?2013 rohm co., ltd. all rights reserved. 46/53 11.dec.2013 rev.003 tsz22111 ? 15 ? 001 ba8391g ba10393f BA10339XX ba2903xxx ba2903sxxx ba2903wxx ba2901xx ba2901sxx physical dimension tape and reel information package name ssop5 http://
datasheet www.rohm.com tsz02201-0rfr0g200200-1-2 ?2013 rohm co., ltd. all rights reserved. 47/53 11.dec.2013 rev.003 tsz22111 ? 15 ? 001 ba8391g ba10393f BA10339XX ba2903xxx ba2903sxxx ba2903wxx ba2901xx ba2901sxx physical dimension tape and reel information - continued package name sop8 ? order quantity needs to be multiple of the minimum quantity. embossed carrier tape tape quantity direction of feed the direction is the 1pin of product is at the upper left when you hold reel on the left hand and you pull out the tape on the right hand 2500pcs e2 () direction of feed reel 1pin (unit : mm) pkg : sop8 drawing no. : ex112-5001-1 (max 5.35 (include.burr)) http://
datasheet www.rohm.com tsz02201-0rfr0g200200-1-2 ?2013 rohm co., ltd. all rights reserved. 48/53 11.dec.2013 rev.003 tsz22111 ? 15 ? 001 ba8391g ba10393f BA10339XX ba2903xxx ba2903sxxx ba2903wxx ba2901xx ba2901sxx physical dimension tape and reel information - continued package name ssop-b8 ? order quantity needs to be multiple of the minimum quantity. embossed carrier tape tape quantity direction of feed the direction is the 1pin of product is at the upper left when you hold reel on the left hand and you pull out the tape on the right hand 2500pcs e2 () direction of feed reel 1pin http://
datasheet www.rohm.com tsz02201-0rfr0g200200-1-2 ?2013 rohm co., ltd. all rights reserved. 49/53 11.dec.2013 rev.003 tsz22111 ? 15 ? 001 ba8391g ba10393f BA10339XX ba2903xxx ba2903sxxx ba2903wxx ba2901xx ba2901sxx physical dimension tape and reel information - continued package name msop8 direction of feed reel ? order quantity needs to be multiple of the minimum quantity. embossed carrier tape tape quantity direction of feed the direction is the 1pin of product is at the upper right when you hold reel on the left hand and you pull out the tape on the right hand 3000pcs tr () 1pin http://
datasheet www.rohm.com tsz02201-0rfr0g200200-1-2 ?2013 rohm co., ltd. all rights reserved. 50/53 11.dec.2013 rev.003 tsz22111 ? 15 ? 001 ba8391g ba10393f BA10339XX ba2903xxx ba2903sxxx ba2903wxx ba2901xx ba2901sxx physical dimension tape and reel information - continued package name sop14 ? order quantity needs to be multiple of the minimum quantity. embossed carrier tape tape quantity direction of feed the direction is the 1pin of product is at the upper left when you hold reel on the left hand and you pull out the tape on the right hand 2500pcs e2 () direction of feed reel 1pin (unit : mm) pkg : sop14 drawing no. : ex113-5001 (max 9.05 (include.burr)) http://
datasheet www.rohm.com tsz02201-0rfr0g200200-1-2 ?2013 rohm co., ltd. all rights reserved. 51/53 11.dec.2013 rev.003 tsz22111 ? 15 ? 001 ba8391g ba10393f BA10339XX ba2903xxx ba2903sxxx ba2903wxx ba2901xx ba2901sxx physical dimension tape and reel information - continued package name ssop-b14 ? order quantity needs to be multiple of the minimum quantity. embossed carrier tape tape quantity direction of feed the direction is the 1pin of product is at the upper left when you hold reel on the left hand and you pull out the tape on the right hand 2500pcs e2 () direction of feed reel 1pin http://
datasheet www.rohm.com tsz02201-0rfr0g200200-1-2 ?2013 rohm co., ltd. all rights reserved. 52/53 11.dec.2013 rev.003 tsz22111 ? 15 ? 001 ba8391g ba10393f BA10339XX ba2903xxx ba2903sxxx ba2903wxx ba2901xx ba2901sxx marking diagrams product name package type marking ba8391 g ssop5 d6 ba10393 f sop8 10393 ba10339 f sop14 ba10339f fv ssop-b14 339 ba2903 f sop8 2903 fv ssop-b8 fvm msop8 ba2903w f sop8 fv ssop-b8 ba2903s f sop8 2903s fv ssop-b8 03s fvm msop8 2903s ba2901 f sop14 ba2901f fv ssop-b14 2901 ba2901s f sop14 2901s fv ssop-b14 sop8 (top view) part number marking lot number 1pin mark sop14 (top view) part number marking lot number 1pin mark ssop-b8 (top view) part number marking lot number 1pin mark ssop-b14 (top view) part number marking lot number 1pin mark msop8 (top view) part number marking lot number 1pin mark part number marking ssop5(top view) lot number http://
datasheet www.rohm.com tsz02201-0rfr0g200200-1-2 ?2013 rohm co., ltd. all rights reserved. 53/53 11.dec.2013 rev.003 tsz22111 ? 15 ? 001 ba8391g ba10393f BA10339XX ba2903xxx ba2903sxxx ba2903wxx ba2901xx ba2901sxx e mie ? 2 b2 e land pattern data all dimensions in mm pkg land pitch e land space mie land length R? 2 land width b2 ssop5 0.95 2.4 1.0 0.6 sop8 sop14 1.27 4.60 1.10 0.76 ssop-b8 ssop-b14 0.65 4.60 1.20 0.35 msop8 0.65 2.62 0.99 0.35 revision history date revision changes 23.aug.2013 001 new release 27.nov.2013 002 add the db notation in large signal voltage gain 11.dec.2013 003 input offset voltage unit is changed from ma to mv in page.1. ssop5 sop8, sop14, ssop-b8 ssop-b14, msop8 mie ? 2 b 2 e http://
datasheet d a t a s h e e t notice - ge rev.002 ? 2014 rohm co., ltd. all rights reserved. notice precaution on using rohm products 1. our products are designed and manufac tured for application in ordinary elec tronic equipments (such as av equipment, oa equipment, telecommunication equipment, home electroni c appliances, amusement equipment, etc.). if you intend to use our products in devices requiring ex tremely high reliability (such as medical equipment (note 1) , transport equipment, traffic equipment, aircraft/spacecra ft, nuclear power controllers, fuel c ontrollers, car equipment including car accessories, safety devices, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or serious damage to property (?specific applications?), please consult with the rohm sale s representative in advance. unless otherwise agreed in writing by rohm in advance, ro hm shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of any ro hm?s products for specific applications. (note1) medical equipment classification of the specific applications japan usa eu china class class class b class class class 2. rohm designs and manufactures its products subject to strict quality control system. however, semiconductor products can fail or malfunction at a certain rate. please be sure to implement, at your own responsibilities, adequate safety measures including but not limited to fail-safe desi gn against the physical injury, damage to any property, which a failure or malfunction of our products may cause. the following are examples of safety measures: [a] installation of protection circuits or other protective devices to improve system safety [b] installation of redundant circuits to reduce the impact of single or multiple circuit failure 3. our products are designed and manufactured for use under standard conditions and not under any special or extraordinary environments or conditio ns, as exemplified below. accordin gly, rohm shall not be in any way responsible or liable for any damages, expenses or losses arising from the use of an y rohm?s products under any special or extraordinary environments or conditions. if you intend to use our products under any special or extraordinary environments or conditions (as exemplified bel ow), your independent verification and confirmation of product performance, reliability, etc, prior to use, must be necessary: [a] use of our products in any types of liquid, incl uding water, oils, chemicals, and organic solvents [b] use of our products outdoors or in places where the products are exposed to direct sunlight or dust [c] use of our products in places where the products ar e exposed to sea wind or corrosive gases, including cl 2 , h 2 s, nh 3 , so 2 , and no 2 [d] use of our products in places where the products are exposed to static electricity or electromagnetic waves [e] use of our products in proximity to heat-producing components, plastic cords, or other flammable items [f] sealing or coating our products with resin or other coating materials [g] use of our products without cleaning residue of flux (ev en if you use no-clean type fluxes, cleaning residue of flux is recommended); or washing our products by using water or water-soluble cleaning agents for cleaning residue after soldering [h] use of the products in places subject to dew condensation 4. the products are not subjec t to radiation-proof design. 5. please verify and confirm characteristics of the final or mounted products in using the products. 6. in particular, if a transient load (a large amount of load applied in a short per iod of time, such as pulse. is applied, confirmation of performance characteristics after on-boar d mounting is strongly recomm ended. avoid applying power exceeding normal rated power; exceeding the power rating under steady-state loading c ondition may negatively affect product performance and reliability. 7. de-rate power dissipation (pd) depending on ambient temper ature (ta). when used in seal ed area, confirm the actual ambient temperature. 8. confirm that operation temperat ure is within the specified range descr ibed in the product specification. 9. rohm shall not be in any way responsible or liable for fa ilure induced under deviant condi tion from what is defined in this document. precaution for mounting / circuit board design 1. when a highly active halogenous (chlori ne, bromine, etc.) flux is used, the resi due of flux may negatively affect product performance and reliability. 2. in principle, the reflow soldering method must be used; if flow soldering met hod is preferred, please consult with the rohm representative in advance. for details, please refer to rohm mounting specification http://
datasheet d a t a s h e e t notice - ge rev.002 ? 2014 rohm co., ltd. all rights reserved. precautions regarding application examples and external circuits 1. if change is made to the constant of an external circuit, pl ease allow a sufficient margin c onsidering variations of the characteristics of the products and external components, including transient characteri stics, as well as static characteristics. 2. you agree that application notes, re ference designs, and associated data and in formation contained in this document are presented only as guidance for products use. theref ore, in case you use such information, you are solely responsible for it and you must exercise your own independent verification and judgment in the use of such information contained in this document. rohm shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of such information. precaution for electrostatic this product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. please take proper caution in your manufacturing process and storage so that voltage exceeding t he products maximum rating will not be applied to products. please take special care under dry condit ion (e.g. grounding of human body / equipment / solder iron, isolation from charged objects, se tting of ionizer, friction prevention and temperature / humidity control). precaution for storage / transportation 1. product performance and soldered connections may deteriora te if the products are stor ed in the places where: [a] the products are exposed to sea winds or corros ive gases, including cl2, h2s, nh3, so2, and no2 [b] the temperature or humidity exceeds those recommended by rohm [c] the products are exposed to di rect sunshine or condensation [d] the products are exposed to high electrostatic 2. even under rohm recommended storage c ondition, solderability of products out of recommended storage time period may be degraded. it is strongly recommended to confirm sol derability before using products of which storage time is exceeding the recommended storage time period. 3. store / transport cartons in the co rrect direction, which is indicated on a carton with a symbol. otherwise bent leads may occur due to excessive stress applied when dropping of a carton. 4. use products within the specified time after opening a hum idity barrier bag. baking is required before using products of which storage time is exceeding the recommended storage time period. precaution for product label qr code printed on rohm products label is for rohm?s internal use only. precaution for disposition when disposing products please dispose them proper ly using an authorized industry waste company. precaution for foreign exchange and foreign trade act since our products might fall under cont rolled goods prescribed by the applicable foreign exchange and foreign trade act, please consult with rohm representative in case of export. precaution regarding intellectual property rights 1. all information and data including but not limited to application example contain ed in this document is for reference only. rohm does not warrant that foregoi ng information or data will not infringe any intellectual property rights or any other rights of any third party regarding such information or data. rohm shall not be in any way responsible or liable for infringement of any intellectual property rights or ot her damages arising from use of such information or data.: 2. no license, expressly or implied, is granted hereby under any intellectual property rights or other rights of rohm or any third parties with respect to the information contained in this document. other precaution 1. this document may not be reprinted or reproduced, in whol e or in part, without prior written consent of rohm. 2. the products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written consent of rohm. 3. in no event shall you use in any wa y whatsoever the products and the related technical information contained in the products or this document for any military purposes, incl uding but not limited to, the development of mass-destruction weapons. 4. the proper names of companies or products described in this document are trademarks or registered trademarks of rohm, its affiliated companies or third parties. http://
datasheet datasheet notice ? we rev.001 ? 2014 rohm co., ltd. all rights reserved. general precaution 1. before you use our pro ducts, you are requested to care fully read this document and fully understand its contents. rohm shall n ot be in an y way responsible or liabl e for fa ilure, malfunction or acci dent arising from the use of a ny rohms products against warning, caution or note contained in this document. 2. all information contained in this docume nt is current as of the issuing date and subj ec t to change without any prior notice. before purchasing or using rohms products, please confirm the la test information with a rohm sale s representative. 3. the information contained in this doc ument is provi ded on an as is basis and rohm does not warrant that all information contained in this document is accurate an d/or error-free. rohm shall not be in an y way responsible or liable for an y damages, expenses or losses incurred b y you or third parties resulting from inaccur acy or errors of or concerning such information. http://

▲Up To Search▲

Price & Availability of BA10339XX

	To Download BA10339XX Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .